Datasheet Texas Instruments TPS2350PW

ManufacturerTexas Instruments
SeriesTPS2350
Part NumberTPS2350PW
Datasheet Texas Instruments TPS2350PW

Hot Swap Power Manager For Redundant -48V Supplies 14-TSSOP -40 to 85

Datasheets

TPS2350 Hot Swap datasheet
PDF, 1.1 Mb, Revision: D, File published: Oct 7, 2013
Extract from the document

Prices

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

Packaging

Pin14
Package TypePW
Industry STD TermTSSOP
JEDEC CodeR-PDSO-G
Package QTY90
CarrierTUBE
Device MarkingTPS2350
Width (mm)4.4
Length (mm)5
Thickness (mm)1
Pitch (mm).65
Max Height (mm)1.2
Mechanical DataDownload

Parametrics

Channel(s) Controlled1
Current Limit Function EnabledAlways
Design SupportCalculation Tool,EVM,Reference Design,Simulation Model,Software
FET ProtectionN/A
Operating Temperature Range-40 to 85 C
Package GroupTSSOP
Package Size: mm2:W x L14TSSOP: 32 mm2: 6.4 x 5(TSSOP) PKG
Special Featuresdi/dT Control,Oring Control
Vabsmax_cont-100 V
Vin(Max)-12 V
Vin(Min)-80 V

Eco Plan

RoHSCompliant

Design Kits & Evaluation Modules

  • Evaluation Modules & Boards: TPS2350EVM
    Telecom -48V OR-ing Diode replacement product TPS2350 Eval Module
    Lifecycle Status: Active (Recommended for new designs)

Application Notes

  • Boosting Supply Select Hysteresis on the TPS2350
    PDF, 54 Kb, File published: Aug 29, 2003
    This application note describes a method for increasing hysteresis in the TPS2350 supply select comparator. Hysteresis greater than the default value of 400 mV might be required due to dynamic loads, poorly regulated supplies, resistive supply lines, or simply to reduce switching between primary and back-up supply. The example given shows how to increase the hysteresis in a -48-V system from 400 m
  • -48-V Supply Selection Circuit For TPS2350 Simplifies Fault Detection in ATCA (Rev. C)
    PDF, 56 Kb, Revision: C, File published: Aug 15, 2006
  • TPS2350, A High-Negative Voltage ORing Controller
    PDF, 354 Kb, File published: May 8, 2008
    This application note addresses a method to OR the high side of the power source as well as the low side using N-channel MOSFETs, thus replacing diodes D1 and D2 with more efficient MOSFETs in the high current path. The MOSFET switch of the return current is referred to here as the high side switch. A circuit schematic for high side switching is recommended and component selection discussed. Hi
  • TPS2350 With High-Side Switch
    PDF, 359 Kb, File published: Apr 17, 2008
    This application note addresses a method to OR the high side of the power source as well as the low side using N-channel MOSFETs, thus replacing diodes D1 and D2 with more efficient MOSFETs in the high current path. The MOSFET switch of the return current is referred to here as the high side switch. A circuit schematic for high side switching is recommended and component selection discussed. High
  • Positive System Reset
    PDF, 48 Kb, File published: Jun 23, 2006

Model Line

Manufacturer's Classification

  • Semiconductors > Power Management > Protection, Monitoring and Hot Swap > Hot Swap and ORing Control Combination
EMS supplier