Datasheet Texas Instruments TPS61026DRCR

Manufacturer	Texas Instruments
Series	TPS61026
Part Number	TPS61026DRCR

5.0-V Output, 1.8-A Switch, 96% Efficient Boost Converter w/ LDO Down-Mode, QFN-10 10-VSON -40 to 85

Datasheets

Download

PDF, 1.2 Mb, Revision: G, File published: Dec 24, 2014

Extract from the document

Prices

Status

Lifecycle Status	Active (Recommended for new designs)
Manufacture's Sample Availability	No

Packaging

Pin	10
Package Type	DRC
Industry STD Term	VSON
JEDEC Code	S-PDSO-N
Package QTY	3000
Carrier	LARGE T&R
Device Marking	BRD
Width (mm)	3
Length (mm)	3
Thickness (mm)	.9
Pitch (mm)	.5
Max Height (mm)	1
Mechanical Data	Download

Parametrics

Duty Cycle(Max)	100 %
Iq(Typ)	0.025 mA
Operating Temperature Range	-40 to 85 C
Package Group	VSON
Rating	Catalog
Regulated Outputs	1
Special Features	Enable,Light Load Efficiency,Load Disconnect,Power Good
Switch Current Limit(Min)	1.5 A
Switch Current Limit(Typ)	1.8 A
Switching Frequency(Max)	720 kHz
Switching Frequency(Min)	480 kHz
Type	Converter
Vin(Max)	5.5 V
Vin(Min)	0.9 V
Vout(Max)	5 V
Vout(Min)	5 V

Eco Plan

RoHS

Compliant

Application Notes

Download
TPS6102x Boost Converter Down Conversion Mode
PDF, 159 Kb, File published: Dec 16, 2004
The TPS61020 is a highly integrated, low-power, boost converter ideally suited for portable battery-powered equipment. The integrated down conversion mode allows the boost converter to operate with the input voltage greater than the output voltage, which is normally only possible with more complicated converters.
Download
Factors That Determine Light Load PSM Switch Freq for TPS6102x Boost Converters
PDF, 528 Kb, File published: Apr 21, 2006
Download
Five Steps to a Good PCB Layout of the Boost Converter
PDF, 701 Kb, File published: May 3, 2016
Download
Minimizing Ringing at the Switch Node of a Boost Converter
PDF, 201 Kb, File published: Sep 15, 2006
The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter.
Download
Design considerations for a resistive feedback divider in a DC/DC converter
PDF, 393 Kb, File published: Apr 26, 2012
Download
Basic Calculation of a Boost Converter's Power Stage (Rev. C)
PDF, 186 Kb, Revision: C, File published: Jan 8, 2014
This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed.
Download
Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)
PDF, 1.1 Mb, Revision: A, File published: May 11, 2015
Download
Extending the Soft Start Time Without a Soft Start Pin (Rev. B)
PDF, 387 Kb, Revision: B, File published: Jun 15, 2017
Download
Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain Outputs
PDF, 130 Kb, File published: Sep 19, 2011
Download
QFN and SON PCB Attachment (Rev. B)
PDF, 821 Kb, Revision: B, File published: Aug 24, 2018
Download
IQ: What it is what it isn’t and how to use it
PDF, 198 Kb, File published: Jun 17, 2011
Download
Performing Accurate PFM Mode Efficiency Measurements (Rev. A)
PDF, 418 Kb, Revision: A, File published: Dec 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.

Model Line

Series: TPS61026 (3)

TPS61026DRCR TPS61026DRCT TPS61026DRCTG4

Manufacturer's Classification

Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)