Datasheet Texas Instruments LM5576MHX

ManufacturerTexas Instruments
SeriesLM5576
Part NumberLM5576MHX
Datasheet Texas Instruments LM5576MHX

SIMPLE SWITCHERВ® 6V to 75V, 3A Wide Vin Step-Down Regulator 20-HTSSOP -40 to 125

Datasheets

LM5576/-Q1 SIMPLE SWITCHERВ® 75 V, 3 A Step-Down Switching Regulator datasheet
PDF, 1.2 Mb, Revision: J, File published: Mar 3, 2014
Extract from the document

Prices

Status

Lifecycle StatusNRND (Not recommended for new designs)
Manufacture's Sample AvailabilityNo

Packaging

Pin2020
Package TypePWPPWP
Industry STD TermHTSSOPHTSSOP
JEDEC CodeR-PDSO-GR-PDSO-G
Device MarkingMHLM5576
Width (mm)4.44.4
Length (mm)6.56.5
Thickness (mm)11
Pitch (mm).65.65
Max Height (mm)1.21.2
Mechanical DataDownloadDownload

Replacements

ReplacementLM5576MHX/NOPB
Replacement CodeS

Parametrics

Approx. Price (US$)2.60 | 1ku
Control ModeCurrent Mode
Duty Cycle(Max)(%)95
Iout(Max)(A)3
Iq(Typ)(mA)1
Operating Temperature Range(C)-40 to 125
Package GroupHTSSOP
RatingCatalog
Regulated Outputs(#)1
Special FeaturesEnable
Tracking
Switching Frequency(Max)(kHz)500
Switching Frequency(Min)(kHz)50
TypeConverter
Vin(Max)(V)75
Vin(Min)(V)6
Vout(Max)(V)70
Vout(Min)(V)1.23

Eco Plan

RoHSNot Compliant
Pb FreeNo

Design Kits & Evaluation Modules

  • Evaluation Modules & Boards: LM5576EVAL
    75V, 3A Step-Down Switching Regulator Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

Application Notes

  • Quick Start Guide for a 3 Amp Buck Regulator Using the LM5576 and LM25576 (Rev. B)
    PDF, 63 Kb, Revision: B, File published: Apr 23, 2013
    This application note provides an easy to use process to design a 3 Amp buck regulator using the LM5576and LM25576 switching regulators.
  • Understanding and Applying Current-Mode Control Theory
    PDF, 409 Kb, File published: Aug 19, 2007
  • AN-1997 Error Amplifier Limitations in High-Performance Regulator Applications (Rev. A)
    PDF, 153 Kb, Revision: A, File published: May 6, 2013
    The development of realistic predictions to assist the power supply engineer during the control loop design process is facilitated in this application report by appropriate small-signal and bode plot analysis, the validity of which is verified through simulation results.
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revision: C, File published: Apr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A)
    PDF, 512 Kb, Revision: A, File published: Sep 12, 2014
    Printed Circuit Board (PCB) layout for Switched Mode Power Supplies (SMPS) is critical to achieve proper converter operation good thermal performance and excellent radiated EMI performance. Optimized board layout for low radiated EMI is made very simple by the package and pin arrangement of the SIMPLE SWITCHER Synchronous Buck Converter family LM4360x and LM4600x
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revision: B, File published: Apr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revision: A, File published: Apr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revision: B, File published: May 3, 2004
    Application Note 643 EMI/RFI Board Design
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revision: A, File published: Apr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revision: C, File published: Apr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revision: B, File published: Apr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revision: A, File published: Apr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revision: C, File published: Apr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revision: C, File published: Apr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revision: C, File published: Apr 19, 2016
  • Input and Output Capacitor Selection
    PDF, 219 Kb, File published: Sep 19, 2005

Model Line

Manufacturer's Classification

  • Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Down (Buck) > Buck Converter (Integrated Switch)