Datasheet Texas Instruments MSP430AFE233

ManufacturerTexas Instruments
SeriesMSP430AFE233
Datasheet Texas Instruments MSP430AFE233

16-bit Ultra-Low-Power Microcontroller, 8KB Flash, 512B RAM, 3x SD24

Datasheets

MSP430AFE2x3, MSP430AFE2x2, MSP430AFE2x1 Mixed Signal Microcontroller datasheet
PDF, 1.4 Mb, Revision: A, File published: Mar 21, 2011
Extract from the document

Prices

Status

MSP430AFE233IPWMSP430AFE233IPWR
Lifecycle StatusActive (Recommended for new designs)Active (Recommended for new designs)
Manufacture's Sample AvailabilityYesNo

Packaging

MSP430AFE233IPWMSP430AFE233IPWR
N12
Pin2424
Package TypePWPW
Industry STD TermTSSOPTSSOP
JEDEC CodeR-PDSO-GR-PDSO-G
Package QTY602000
CarrierTUBELARGE T&R
Device Marking430AFE233430AFE233
Width (mm)4.44.4
Length (mm)7.87.8
Thickness (mm)11
Pitch (mm).65.65
Max Height (mm)1.21.2
Mechanical DataDownloadDownload

Parametrics

Parameters / ModelsMSP430AFE233IPW
MSP430AFE233IPW
MSP430AFE233IPWR
MSP430AFE233IPWR
ADCSigmaDelta24 - 3chSigmaDelta24 - 3ch
AESN/AN/A
Active Power, uA/MHz220220
Additional FeaturesWatchdog,Temp Sensor,Brown Out ResetWatchdog,Temp Sensor,Brown Out Reset
BSLUARTUART
CPUMSP430MSP430
Frequency, MHz1212
GPIO Pins1111
Max VCC3.63.6
Min VCC1.81.8
Multiplier16x1616x16
Non-volatile Memory, KB88
Operating Temperature Range, C-40 to 85-40 to 85
Package GroupTSSOPTSSOP
Package Size: mm2:W x L, PKG24TSSOP: 50 mm2: 6.4 x 7.8(TSSOP)24TSSOP: 50 mm2: 6.4 x 7.8(TSSOP)
RAM, KB0.50.5
RatingCatalogCatalog
SPI11
Special I/ON/AN/A
Standby Power, LPM3-uA0.50.5
Timers - 16-bit11
UART11
Wakeup Time, us11

Eco Plan

MSP430AFE233IPWMSP430AFE233IPWR
RoHSCompliantCompliant

Application Notes

  • Implementation of a Single-Phase Electronic Watt-Hour Meter Using MSP430AFE2xx (Rev. A)
    PDF, 2.0 Mb, Revision: A, File published: May 10, 2013
    This application report describes the implementation of a single-phase electronic electricity meter using the Texas Instruments MSP430AFE2xx metering processors. It includes the necessary information with regard to metrology software and hardware procedures for this single chip implementation.
  • Interfacing the MSP430AFE2xx Based Single-Phase E-Meter with a Host Processor
    PDF, 1.2 Mb, File published: Sep 24, 2014
    This application report describes the implementation of a single-phase electronic electricity meter using the Texas Instruments MSP430AFE25x metrology family of processors in two-chip architecture. The metering processor (MSP430AFE25x) assumes the role of a slave controlled by a host microcontroller (MCU), the MSP430F663x.
  • Energy Measurement Results for TI Designed Meter Using MSP430AFE2xx Devices
    PDF, 763 Kb, File published: Jul 30, 2012
    This application report describes the results obtained on a single phase electronic electricity meter using the Texas Instruments MSP430AFE2xx metering processors. These tests are indicative of the performance of a meter designed by Texas Instruments and is subject to differ based on sensor selection, board layouts and other design considerations. The results include energy accuracies for active a
  • Programming With the MSP430AFE2xx Family and the MSP430i20xx Family
    PDF, 89 Kb, File published: Aug 10, 2014
    This application report enables the easy incorporation of the MSP430AFE2xx family of MCUs, featuring the SD24_A module, as well as the MSP430i20xx family of MCUs, which features the SD24 module, into new designs. It covers programming, system, and peripheral considerations when creating firmware. The intent is to highlight a few key differences between the two families and how to incorporate each
  • Migrating from the MSP430F2xx,G2xx Family to the MSP430FR58xx/FR59xx/68xx/69xx (Rev. E)
    PDF, 179 Kb, Revision: E, File published: Nov 3, 2016
    This application report enables easy migration from MSP430F2xx flash-based MCUs to the MSP430FR58xx/FR59xx/68xx/69xx family of FRAM-based MCUs. For the migration guide to MSP430FR57xx, see Migrating From the MSP430F2xx Family to the MSP430FR57xx Family. It covers programming, system, and peripheral considerations when migrating firmware. The intent is to highlight key differences between the two f
  • Design Considerations When Using the MSP430 Graphics Library
    PDF, 475 Kb, File published: Oct 5, 2012
    LCDs are a growing commodity in todays market with products as diverse as children's toys to medical devices. Modern LCDs, along with the graphics displayed on them, are growing in complexity. A graphics library can simplify and accelerate development while creating the desired user experience. TI provides the MSP430 Graphics Library for use in developing products with the MSP430в„ў MCU. This
  • MSP Code Protection Features
    PDF, 752 Kb, File published: Dec 7, 2015
    MSP microcontrollers (MCUs) offer a number of features to help control code accessibility in the device, to add different layers of code access management and protection strategies. These include features that can lock or password protect the JTAG/SBW access, IP Encapsulation (IPE) to isolate sensitive code with different permissions than the rest of the program, and bootloader (BSL) access featur
  • ESD Diode Current Specification
    PDF, 520 Kb, File published: Dec 7, 2015
    This document explains the maximum ESD diode current specified for GPIO on MSP microcontrollers. Sometimes signals on specific pins exceed the supply of the MSP MCU. In such a case, the device can handle this overvoltage condition through the ESD diodes, but the ESD diode specification must be considered during application design. The items to be considered are described in this document.

Model Line

Series: MSP430AFE233 (2)

Manufacturer's Classification

  • Semiconductors> Microcontrollers (MCU)> MSP430 ultra-low-power MCUs> MSP430F2x/4x
EMS supplier