RadioLocman.com Electronics ru
Advanced Search +
  
Go Back   RadioLocman Forum > Electronics and ... > Microcontrollers (MCU)

Microcontrollers (MCU) Application and programming of MCUs, Evaluation Kits and Demonstration Boards, Programmers.

Reply
 
Thread Tools Search this Thread
Old 10-06-2013, 03:04 PM   #1
Radiolocman Robot
Member
 
Join Date: Jan 2011
Posts: 226
Radiolocman Robot is on a distinguished road
Default Discussion: AVR Programmer

Quote:
About AVR Programmer This simple AVR Programmer will allow you to painlessly transfer hex programs to most ATMEL AVR microcontrollers without sacrificing your budget and time. It is more reliable than most other simple AVR programmers available out there and can be built in very short amount of time.
More: AVR Programmer
Radiolocman Robot is offline   Reply With Quote
Old 10-06-2013, 03:04 PM   #2
mototsдge
Junior Member
 
Join Date: Oct 2013
Posts: 1
mototsдge is on a distinguished road
Default

Cann this Programmer to be used for Attiny26?

Thanks
mototsдge is offline   Reply With Quote
Old 10-07-2013, 08:22 PM   #3
Vadzz
Member
 
Join Date: Jan 2011
Posts: 65
Vadzz is on a distinguished road
Default

Greetings. This device is, if correctly and without errors is constructed, it can be used for many AVR microcontrollers (used Ponyprog).
Vadzz is offline   Reply With Quote
Old 10-23-2013, 01:49 PM   #4
Anatoly
Member
 
Join Date: Oct 2013
Posts: 58
Anatoly is on a distinguished road
Default

Can I work with the PIC microcontroller?
Anatoly is offline   Reply With Quote
Old 10-24-2013, 12:46 PM   #5
Vadzz
Member
 
Join Date: Jan 2011
Posts: 65
Vadzz is on a distinguished road
Default

This programmer is not suitable for PIC microcontrollers...
Vadzz is offline   Reply With Quote
Old 01-08-2019, 04:17 PM   #6
Em_13
Junior Member
 
Join Date: Feb 2016
Posts: 18
Em_13 is on a distinguished road
Default

Hello. I assembled this progromoter for ATtiny 2313 firmware all working
Em_13 is offline   Reply With Quote
Old 06-28-2019, 05:58 PM   #7
CobbKanki
Junior Member
 
Join Date: Jun 2019
Posts: 1
CobbKanki is on a distinguished road
Default

Hi..i have built the one using the Arduino and there the NPN is used to pull the RESET pin low... but the signal being supplied by the pin is a) not 5V compatible b) going positive when triggered, so it's an Inverter as well as a guarantee that the pin get's clearly pulled to correct low logic level relative to the CHIP. The Zener diodes provide a similar guarantee that the chip sees a TTL 5Volt logic level but the related CHIP pins do not need logic "inversion".

pcb assembly

Last edited by CobbKanki; 08-07-2019 at 08:26 PM.
CobbKanki is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Discussion: AVR programmer Olimex AVR-PG1 Radiolocman Robot Microcontrollers (MCU) 2 08-13-2013 05:26 PM
Discussion: µProg - tiny, fast, portable AVR programmer with SD. Part 3. Software, Memory card, files, Firmware update, Demonstration Radiolocman Robot Microcontrollers (MCU) 2 03-25-2013 09:40 PM
Discussion: ATMEL AVR ISP Programmer that Works with AVRStudio4 Radiolocman Robot Microcontrollers (MCU) 2 05-12-2011 06:55 AM

All times are GMT. The time now is 12:17 AM.




Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus