Circuits & Schematics: frequency meter - 2
Search for: "frequency meter"
- .. bridge is a cumbersome process. Figure 1. A simple VFC uses its internal reference to produce a serial pulse train whose frequency is inversely proportional to unknown capacitance CX. Options for measuring the VFC’s output ...Nov 9, 2016
- Stephen Woodward.. 0.3%/ C. Meanwhile, optical sensor O 1 works with a free-spinning anemometer impeller to produce wind-speed-proportional frequency: F W = 10 Hz/m/sec. Conversion of V Q1 and F W into a 1-mV = 1 W/m 2 output signal is then the function ...
.. In combination, they provide a real-time, linear, temperature-compensated readout of wind-power density. Figure 1. This meter circuit uses a free-spinning anemometer and a diode-connected transistor temperature sensor to measure the ...Jan 29, 2018
- .. have to write the software from scratch. But I felt that the Atmega328 was just too much of an overkill just to measure a frequency and control an LCD. They are quite a bit more expensive than the PIC, CHF 3.70 compared to CHF 1.90 ...
.. Fässler soldernerd.com Some of you may have seen my arduino-based inductance meter in the article [1]. The arduino-based meter works well and made a great proof-of-concept. But for everyday use ...Aug 21, 2018 - .. by simply connecting a tuned circuit to its input. It turned out that it was possible to create a simple tuned radio frequency (TRF) receiver by implementing the two features of the LM386 mentioned earlier and using a tuned ...
.. When constructed with a LM386 manufactured by either National Semi or Samsung, this configuration can receive both the 80 meter and 40 meter amateur bands up to 8 MHz. Figure 5. The LM386 can be used to create a shortwave regenerative ...Jun 18, 2020 - .. and should be readable and modifiable as desired in any case a few comments follow. #define F_CPU 2457600UL // crystal frequency #define PWM_TOP F_CPU/60 // == 40960 is TOP count for timer 0 (goes into OCR0A) These pre-compiler ...
.. software can be modified to display different things like a voltage at an analog input of the micro making a LASER analog meter. Or to make something like a LASER chronulator. More of these circuits can be superimposed to display different ...Jun 10, 2009 - .. transistor to make a most unusual capacitance beeper probe. When a capacitor is touched to the probe, the probe beeps at a frequency that varies with capacitance. The frequency change is so steep with capacitance that tiny capacitors ...
.. C-Beeper will become indispensable in virtually no time! Quickly match capacitors and trimmers. Forget the capacitance meter when matching parts from the parts bin or selecting a fixed value to replace a trimmer - the fingers as ...Nov 12, 2008 - .. An electromagnetic field probe designed to detect changing electric and magnetic fields. The probe has switchable gain, a frequency response up to 400kHz and independent audio and meter monitoring. Click to enlarge Circuit Notes This ...Sep 7, 2010
- .. If the second hand is re-attached, then you don't have to wait very long to see evidence of the clock counting our timebase frequency - the second hand will advance. The second hand should advance every 59 seconds, and the 'Freq' preset ...
.. 'Freq' preset in the simple timebase should be adjusted until this is the case (if you are lucky enough to own a frequency meter, then adjust for a frequency of 554.83 Hz). Once set, the second hand can be removed again, and the clock ...Feb 12, 2009 - .. IC3 IC4 divide by 10 and drive the displays. P1 resets the counters and P2 enables the displays. IC1C generates an audio frequency square wave that is enabled for a short time at each monostable count. Q1 drives the piezo sounder and ...
.. is avoided because to reset the circuit both pushbuttons must be operated together. Obviously, this is not a precision meter, but its approximation degree was found good for this kind of device. In any case, the most critical thing to ...Aug 4, 2009 - Forrest Cook.. the battery when the battery reaches a preset full voltage. MPPT controllers use an inductor for energy storage and a high frequency switching circuit to transfer the energy to the battery. This circuit is for a shunt-mode charge ...
.. The battery should be pre-charged for easiest alignment. Point the panel at the sun, and monitor the battery voltage with a meter. Adjust the 20 turn 100K potentiometer until the Full LED starts to flash, then tweak the potentiometer until ...Oct 30, 2009
Sort by: relevance / date
