Circuits & Schematics: -Wire Barometer 5/10 Volt Design vrs - 4

Search for: "-Wire Barometer 5/10 Volt Design vrs"
Search results: 1,224 Output: 31-40   Including: Design (1010); Wire (277); Volt (104); 510 (23); Barometer (3); vrs (0).
  1. Jayapal Ramalingam
    .. “DIY RTD for a DMM” ( Ref. 1 ). With a fortnight’s struggle, I completed the design of 4 mA to 20 mA, two-wire temperature transmitter using a platinum resistance temperature detector (RTD) sensor, as shown in Figure 1. ...
    .. an analog circuit can be a frustrating experience, as noted by Nick Cornford in his Design Idea (DI), “DIY RTD for a DMM” ( Ref. 1 ). With a fortnight’s struggle, I completed the ...
    Jun 11, 2025
  1. .. worse) the motherboard. Fan RPM monitoring will NOT work with this temperature control. Don't try to connect the rpm signal wire to your motherboard. It will not work and might damage your motherboard. Building a temperature control that ...
    Apr 28, 2008
  1. .. Try this one from SparkFun Electronics #COM-00104; $0.95 3.7 V battery (SparkFun Electronics #PRT-08818; $4.95) Scrap wire Round flat-top metal container (I used a salvaged Kiwi Brands shoe polish container -- just to prove to some of ...
    Dec 16, 2008
  2. .. such as Molex KK 6471 6 pin Header, such as Molex KK6410 6 pin Housing, such as Molex KK 6471 Crimps, Molex KK 4809 Wire, solid strand and stranded Printed Circuit Board or Perforated Proto board and solid strand wire 10 Normally Open ...
    Sep 7, 2011
  3. V Gopalakrishnan
    .. the wires when the water level falls below the sensors. You can also use any other high-conductivity and noncorrosive wire material in some configurations. The power supply is floating. With few modifications, the circuit in Figure 2 ...
    Aug 4, 2022
  4. .. is using an ATX power supply, with Sparkfun's adapter board(you need this too) and this adapter. You would solder the red wire to 5v on the adapter board, and the black wire to ground. Please note that you must also connect PS_ON to ground. ...
    .. used to supply the additional current, but should NOT be directly connected to the header, as battery voltage varies. A 5 volt voltage regulator, if your battery outputs more than 5 volts, or a voltage stepper, if you battery outputs less ...
    Nov 1, 2011
  5. .. can be used for AM, FM, and Shortwave(SW). On the shortwave band this active antenna is comparable to a 20 to 30 foot wire antenna. It is further more designed to be used on receivers that use untuned wire antennas, such as inexpensive ...
    .. A 470 uH coil works on lower frequencies and lie in AM, for shortwave try a 20 uH coil. This unit can be powered by a 9 volt alkaline battery. If a power supply is used, bypass the power supply with a 0.04 uF capacitor to prevent noise ...
    Feb 10, 2007
  6. .. Salvaged Plastic Project Box Clear Vinyl Sheet (craft store; 50¢) Large Eyelet Kit (craft store; $2.45) Clips Wire NOTE: There are four distinct subassemblies which constitute our eBag: (1) modified messenger bag, (2) ...
    .. batteries are the scourge of cellphone jockeys and iPod people everywhere. But you can avoid volt loss by charging your gadgets while you carry them. Just equip an old messenger bag with a lightweight, ...
    Nov 16, 2007
  7. .. difficult to build but the pen may be built in any number of ways as long as a couple of critical requirements are met. The wire probe sticking into the ion chamber must not touch anything that is ever-so-slightly conductive, not even most ...
    .. from the threading process! This isn't exactly the easy way to build such a pen but it gets the idea across. A tiny 10 A 9 Volt alkaline battery was installed and the threaded nylon bushing was tightened. A little clear epoxy fills the LED ...
    Nov 29, 2007
  8. .. the components, which are shown lying flat on the board, are actually mounted standing upright. The links are bare copper wire on the component side of the board. The heatsinks are folded strips of aluminium, about 2mm thick. Use a ...
    .. above whatever voltage is on pin 2. Since pin 2 is generally connected to ground - the 7805 is usually referred to as a 5-volt regulator. However, R1, C1 Z1 hold pin 2 at 9v1. Therefore the output at pin 3 will be ( 9v1 + 5 = 14v1 ). ...
    Mar 24, 2008

Sort by: relevance / date

Search "-Wire Barometer 5/10 Volt Design vrs" on other search engines: Only-DataSheet.com Google