RadioLocman.com Electronics ru
Advanced Search +
  
» Advanced Technologies
» Analogue Design
» Antique
» Application Notes
» Audio
» Auto-Audio
» Automation
» Automotive
» Bad Prescriptions
» Beginners
» CAD & Software
» Camcorders
» Cellular
» Computers and Peripherals
» Digital
» Domestic
» Games
» High Voltage
» Interfaces
» Laser
» Light
» MCU open-source platforms
» Measurement
» Medicine
» Microcontrollers usage
» Monitors
» Music
» Networks
» Oscillators
» Power
» Radio
» RC Modeling
» Robots
» Satellite
» Security
» Solar
» Supply
» Telephone
» Theory
» Tools and Technologies
» TV
» Video
» Wind Energy
» Wireless
Search results: 233   Output: 31-40
  1. Keith Szolusha EDN In certain dc/dc-converter applications, on-chip, cycle-by-cycle current limit may be insufficient protection to prevent a failure during a short circuit. A nonsynchronous boost converter provides a direct path from the input to ...
    14-12-2016
  2. Bob Smith, Linear Technology Design Note 1036 Introduction The LTC®4370 is a 2-supply current sharing, diode- ORing controller that uses MOSFETs to form ideal diodes. In this way, the LTC4370 can actively balance the output currents of two ...
    Circuits » Supply · Power » Linear Technology » LT1716, LT6650, LTC4370
    02-12-2016
  3. Sajjad Hajdar Electronic Design Most common current-limiting implementations have a voltage drop that’s too high for today's systems with their low-voltage supply rails; this design with its far lower voltage drop is a better fit. There ...
    18-11-2016
  4. Gheorghe Plasoianu EDN Bench electronic loads are usually rated for voltages less than 100 V, which make it difficult to test high-voltage power supplies. This Design Idea offers an alternative: an inexpensive electronic load rated for 500 V or ...
    24-10-2016
  5. Peter Miller EDN Like other simple, single-cell lithium-ion battery chargers, Microchip’s MCP73812 provides no means of indicating the charging status. You can remedy this situation by adding four components (Figure 1). Add one more LED, and ...
    Circuits » Supply · Power » Microchip » MCP73812
    24-10-2016
  6. Chee Hua How EDN This Design Idea demonstrates a way to adjust the output voltage of a power supply, for OVP/UVP testing, margin-testing the load, voltage programmability, or any other reason. The circuit in Figure 1 is capable of bidirectional ...
    Circuits » Supply · Power » Analog Devices » AD623, AD5220, AD8276
    10-10-2016
  7. JB Castro-Miguens, C Castro-Miguens EDN Protect circuits from high current until a capacitor charges A high-power offline supply is nothing more than a half- or full-bridge dc/dc converter. Rectifying the ac line yields a dc voltage that feeds the ...
    10-10-2016
  8. Alan Adamsky Electronic Design The two battery-simulator circuits described here can help you quickly test a battery charger under a normal battery condition and an over-discharged battery condition. The circuits let you set any voltage to see how ...
    Circuits » Measurement · Power » Texas Instruments » LM431, IRFP3703, MTW24N40
    13-09-2016
  9. Jesus Rosales, Linear Technology Design Note 545 Introduction Industrial, telecom, medical and automotive applications use a wide variety of regulated voltages to operate effectively, including high voltage and negative rails. When the designer is ...
    06-09-2016
  10. Peter Baxter EDN This Design Idea shows how to use a 63¢ (Q=1) microprocessor reset voltage detector IC in a relay coil drive circuit to greatly reduce the coil’s hold-in current. When asked to estimate the coil current of a small Omron ...
    06-09-2016
 Pages:

Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus