Datasheet AD8452 (Analog Devices) - 9

AD8452 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 6.
Stresses at or above those listed under Absolute Maximum
Parameter Rating
Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these Analog Supply Voltage (AVCC − AVEE) 36 V or any other conditions above those indicated in the operational PWM Supply Voltage (VIN – DGND) −0.3 V to +61 V section of this specification is not implied. Operation beyond Internal Regulator Voltage (VREG − DGND) 5.5 V the maximum operating conditions for extended periods may Voltage affect product reliability. Input Pins (ISVP, ISVN, BVP, and BVN) AVEE + 40 V Analog Controller and Front-End Pins AVCC − 40 V
THERMAL RESISTANCE
(ISREFH, ISREFL, BVREFL, BVREFH, VREF, Thermal performance is directly linked to printed circuit board VSET, VVP0, BVMEA, VVE0, VVE1, VINT, IVE0, IVE1, ISMEA, ISET) (PCB) design and operating environment. Careful attention to PWM Pins PCB thermal design is required. SYNC, MODE −0.3 V to +5.5 V
Table 7. Thermal Resistance
DH, DL, SS, DMAX, SCFG, DT, FREQ, CLVT −0.3 V to
2
VREG + 0.3 V
Package Type θJA Unit
Current Limit Sense Pins (CLP, CLN) −0.3 V to +61 V ST-481 81 °C/W FAULT Pin and EN Pin −0.3 V to +61 V 1 Dissipation ≤ 0.3, TA = 25°C. Maximum Digital Supply Voltage 2 θJA is the natural convection junction to ambient thermal resistance measured in a one cubic foot sealed enclosure. Positive Analog Supply (VREG − AVCC) 0.3 V Negative Analog Supply (VREG − AVEE) −0.3 V
ESD CAUTION
Maximum Digital Ground Positive Analog Supply (DGND − AVCC) 0.3 V Negative Analog Supply (DGND − AVEE) −0.3 V Maximum Analog Ground Positive Analog Supply (AGND − AVCC) 0.3 V Negative Analog Supply (AGND − AVEE) −0.3 V Analog Ground with Respect to the Digital Ground (AGND − DGND) Maximum 0.3 V Minimum −0.3 V Storage Temperature Range −65°C to +150°C Rev. 0 | Page 8 of 34 Document Outline Features Applications General Description Functional Block Diagram Table of Contents Revision History Specifications Analog Front-End and Controller Specifications Pulse-Width Modulator Specifications Digital Interface Specifications Power Supply Temperature Range Specifications Absolute Maximum Ratings Thermal Resistance ESD Caution Pin Configuration and Function Descriptions Typical Performance Characteristics In-Amp Characteristics Difference Amplifier Characteristics CC and CV Loop Filter Amplifiers and VSET Buffer (except where Noted) Reference Characteristics Pulse-Width Modulator Theory of Operation Introduction Instrumentation Amplifier (In-Amp) Reversing Polarity When Charging and Discharging In-Amp Offset Option Battery Reversal and Overvoltage Protection Difference Amplifier CC and CV Loop Filter Amplifiers Charging Lithium-Ion (Li-Ion) Cells Concepts of Constant Current (CC) and Constant Voltage (CV) Compensation Charge and Discharge Control Conditions to Charge and Discharge a Battery MODE Pin Input and Output Supply Pins Shutdown Undervoltage Lockout (UVLO) Soft Start PWM Drive Signals Peak Current Protection and Diode Emulation (Synchronous) Peak Current-Limit Detection Diode Emulation/Synchronous Mode Operation Frequency and Phase Control Internal Frequency Control External Frequency Control Operating Frequency Phase Shift Maximum Duty Cycle Fault Input Thermal Shutdown (TSD) Applications Information Analog Controller Functional Description Power Supply Connections Current Sense In-Amp Connections Current Sensors Optional Low-Pass Filter Voltage Sense Differential Amplifier Connections Battery Current and Voltage Control Inputs (ISET and VSET) Loop Filter Amplifiers Selecting Charge or Discharge Options Select RCL and RCLVT for the Peak Current Limit Setting the Operating Frequency and Programming the Synchonization Pin Select RFREQ for Standalone or Master Clock Selecting RFREQ for a Slave Device Programming the External Clock Phase Shift Programming the Dead Time Programming the Maximum Duty Cycle Selecting CSS Additional Information Outline Dimensions Ordering Guide