RadioLocman.com Electronics ru
Advanced Search +
  
» Advanced Technologies
» Analogue Design
» Antique
» Application Notes
» Audio
» Auto-Audio
» Automation
» Automotive
» Bad Prescriptions
» Beginners
» CAD & Software
» Camcorders
» Cellular
» Computers and Peripherals
» Digital
» Domestic
» Games
» High Voltage
» Interfaces
» Laser
» Light
» MCU open-source platforms
» Measurement
» Medicine
» Microcontrollers usage
» Monitors
» Music
» Networks
» Oscillators
» Power
» Radio
» RC Modeling
» Robots
» Satellite
» Security
» Solar
» Supply
» Telephone
» Theory
» Tools and Technologies
» TV
» Video
» Wind Energy
» Wireless
Search results: 121   Output: 11-20
  1. Aaron Schultz, Linear Technology Design Note 563 Introduction A new family of op amps features industry leading speed versus supply current. The LTC6261/LTC6262/LTC6263 family (single, dual, quad) provides 30 MHz at a low 240 uA supply current, ...
    Circuits » Analogue Design · Audio » Linear Technology » LTC6261, LTC6262, LTC6263
    02-08-2017
  2. Don Sherman, Maxim Integrated Products EDN With the aid of a simple mounting system and some soldered-on weights, a piezoelectric “bender” can detect mechanical shocks. The bender comprises a piezoelectric-ceramic element bonded to a ...
    02-08-2017
  3. Carlos Castro-Miguens and José Benito Castro-Miguens Electronic Design This circuit shows how to develop inverting and non-inverting programmable gain amplifiers with non-standard gain values to optimize sensor output/ADC input range ...
    02-08-2017
  4. John Guy, Maxim Integrated Products EDN Many approaches for creating notch filters, which reject a narrow band of frequencies and pass all others, are unsatisfactory because they allow the component tolerances to interact. The circuit in Figure 1 ...
    Circuits » Analogue Design » Maxim » MAX4075, MAX4198
    26-07-2017
  5. Doug Glenn EDN The well-documented Sallen-Key active filter is a staple of analog design. This Design Idea shows a way to obtain better roll-off by adding just a few common passive components. Figure 1a shows a typical implementation of a ...
    18-07-2017
  6. Adolfo Garcia EDN The circuit in Figure 1 filters 60-Hz interference from low-frequency, low-level signals. The filter exhibits 40-dB rejection (Q = 0.75) and draws 95 uA max from a single-sided 5 V supply. Figure 1. This notch filter suppresses ...
    18-07-2017
  7. C Castro-Miguens, M Pérez Suárez, JB Castro-Miguens EDN There are many circuits published showing zero-crossing detectors for use with 50- and 60-Hz power lines. Though the circuit variations are plentiful, many have shortcomings. ...
    12-07-2017
  8. Pierre Corbeil EDN Class B amplifiers are prone to crossover distortion, which occurs in the output stage in which conduction transfers from one transistor to the other. To prevent crossover distortion, a bias current must flow in both transistors ...
    15-06-2017
  9. John Ambrose EDN Although you can obtain universal, resistor-programmable switched-capacitor filters that are configurable as notch filters, most cannot operate at bandwidths higher than 100 kHz. Further, the typically 16- to 20-pin packages do not ...
    09-06-2017
  10. Kenneth Gustafsson EDN Some instrumentation amplifiers use external resistors to set their gain. Unfortunately, the lack of temperature-coefficient matching between the external and the internal resistors results in a high gain drift. If, however, ...
    23-05-2017
 Pages:

Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus