RadioLocman.com Electronics ru
Advanced Search +
  

Datasheet Texas Instruments MSP430F6726IPNR

Datasheet Texas Instruments MSP430F6726IPNR

ManufacturerTexas Instruments
SeriesMSP430F6726
Part NumberMSP430F6726IPNR

MSP430F673x, MSP430F672x Mixed Signal Microcontroller 80-LQFP -40 to 85

Datasheets

  • Download » Datasheet, PDF, 1.6 Mb, Revision: C, 02-27-2013
    MSP430F673x, MSP430F672x Mixed Signal Microcontroller datasheet
    Docket ↓
    MSP430F673x
    MSP430F672x
    www.ti.com SLAS731C – DECEMBER 2011 – REVISED FEBRUARY 2013 MIXED SIGNAL MICROCONTROLLER
    FEATURES 1 2 Low Supply Voltage Range:
    3.6 V Down to 1.8 V
    Ultra-Low Power Consumption
    – Active Mode (AM):
    All System Clocks Active
    265 µA/MHz at 8 MHz, 3.0 V, Flash Program
    Execution (Typical)
    140 µA/MHz at 8 MHz, 3.0 V, RAM Program
    Execution (Typical)
    – Standby Mode (LPM3):
    Real-Time Clock With Crystal, Watchdog,
    and Supply Supervisor Operational, Full
    RAM Retention, Fast Wake-Up:
    1.7 µA at 2.2 V, 2.5 µA at 3.0 V (Typical)
    – Off Mode (LPM4):
    Full RAM Retention, Supply Supervisor
    Operational, Fast Wake-Up:
    1.6 µA at 3.0 V (Typical)
    – Shutdown RTC Mode (LPM3.5):
    Shutdown Mode, Active Real-Time Clock ...

Prices

Family: MSP430F6720, MSP430F6721, MSP430F6723, MSP430F6724, MSP430F6725, MSP430F6726, MSP430F6730, MSP430F6731, MSP430F6733, MSP430F6734, MSP430F6735, MSP430F6736

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

Packaging

Pin80
Package TypePN
Industry STD TermLQFP
JEDEC CodeS-PQFP-G
Package QTY1000
CarrierLARGE T&R
Device MarkingF6726
Width (mm)12
Length (mm)12
Thickness (mm)1.4
Pitch (mm).5
Max Height (mm)1.6
Mechanical DataDownload »

Parametrics

ADCADC10 - 6ch,SigmaDelta24 - 2ch
AESN/A
Active Power346 uA/MHz
Additional FeaturesLCD,Real-Time Clock,Watchdog,Temp Sensor,Brown Out Reset,IrDA
BSLUART
CPUMSP430
DMA3
Featuredf6
Frequency25 MHz
GPIO Pins72
I2C1
Max VCC3.6
Min VCC1.8
Multiplier32x32
Non-volatile Memory128 KB
Operating Temperature Range-40 to 85 C
Package GroupLQFP
Package Size: mm2:W x L80LQFP: 196 mm2: 14 x 14(LQFP) PKG
RAM8 KB
RatingCatalog
SPI4
Special I/ON/A
Standby Power2.9 LPM3-uA
Timers - 16-bit4
UART3
Wakeup Time3 us

Eco Plan

RoHSCompliant

Design Kits & Evaluation Modules

  • Evaluation Modules & Boards: MSP-FET430U100B
    100-pin Target Development Board and MSP-FET Programmer Bundle for MSP430F6x MCUs
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: MSP-TS430PZ100B
    MSP-TS430PZ100B - 100-pin Target Development Board for MSP430F6x MCUs
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: EVM430-F6736
    EVM430-F6736 - MSP430F6736 EVM for Metering
    Lifecycle Status: Active (Recommended for new designs)
  • JTAG Emulators/ Analyzers: ENERGYTRACE
    MSP EnergyTrace Technology
    Lifecycle Status: Active (Recommended for new designs)

Application Notes

  • Download » Application Notes, PDF, 74 Kb, 11-12-2013
    Using TI’s DLMS COSEM Library
    This application report describes in detail the usage of DLMS COSEM library developed by Texas Instruments for customers who use TI's microcontrollers in metering applications. The library is provided as object coded with a configuration file for ease of use. The library can be obtained by contacting the regional sales and marketing offices. The customer will have to sign an SLA before getting acc
  • Download » Application Notes, PDF, 2.1 Mb, Revision: A, 07-20-2015
    Designing With MSP430 and Segment LCDs (Rev. A)
    Segment liquid crystal displays (LCDs) are needed to provide information to users in a wide variety of applications from smart meters to electronic shelf labels (ESL) to medical equipment. Several MSP430™ microcontroller families include built-in low-power LCD driver circuitry that allows the MSP430 MCU to directly control the segmented LCD glass. This application note helps explain how segmented
  • Download » Application Notes, PDF, 151 Kb, Revision: D, 11-03-2016
    Migrating from the MSP430F5xx,F6xx Family to the MSP430FR58xx/FR59xx/68xx Family (Rev. D)
    This application report helps enable easy migration from MSP430F5xx and MSP430F6xx flash-based MCUs to the MSP430FR58xx/FR59xx/68xx/69xx FRAM-based MCUs. For the migration guide to MSP430FR57xx, see Migrating From the MSP430F2xx Family to the MSP430FR57xx Family. It covers programming, system, and peripheral considerations when migrating firmware. The intent is to highlight differences between the
  • Download » Application Notes, PDF, 551 Kb, Revision: A, 04-01-2016
    General Oversampling of MSP ADCs for Higher Resolution (Rev. A)
    Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design demands a higher resolution than the ADC of the selected MSP can offer. This application report, which is based on the previously-published Oversampl
  • Download » Application Notes, PDF, 752 Kb, 12-07-2015
    MSP Code Protection Features
    MSP microcontrollers (MCUs) offer a number of features to help control code accessibility in the device, to add different layers of code access management and protection strategies. These include features that can lock or password protect the JTAG/SBW access, IP Encapsulation (IPE) to isolate sensitive code with different permissions than the rest of the program, and bootloader (BSL) access featur
  • Download » Application Notes, PDF, 475 Kb, 10-05-2012
    Design Considerations When Using the MSP430 Graphics Library
    LCDs are a growing commodity in todays market with products as diverse as children's toys to medical devices. Modern LCDs, along with the graphics displayed on them, are growing in complexity. A graphics library can simplify and accelerate development while creating the desired user experience. TI provides the MSP430 Graphics Library for use in developing products with the MSP430™ MCU. This
  • Download » Application Notes, PDF, 520 Kb, 12-07-2015
    ESD Diode Current Specification
    This document explains the maximum ESD diode current specified for GPIO on MSP microcontrollers. Sometimes signals on specific pins exceed the supply of the MSP MCU. In such a case, the device can handle this overvoltage condition through the ESD diodes, but the ESD diode specification must be considered during application design. The items to be considered are described in this document.

Moldel Line

Series: MSP430F6726 (4)

Manufacturer's Classification

  • Semiconductors > Microcontrollers (MCU) > MSP430 ultra-low-power MCUs > MSP430F5x/6x
Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus