Datasheet Texas Instruments TPS60250RTET
| Manufacturer | Texas Instruments |
| Series | TPS60250 |
| Part Number | TPS60250RTET |
High Efficiency Charge Pump for 7 WLEDs with I2C Interface 16-WQFN -40 to 85
Datasheets
High Efficiency Charge Pump for 7 WLEDs with I2C Interface datasheet
PDF, 887 Kb, Revision: C, File published: Apr 23, 2008
Extract from the document
Prices
Status
| Lifecycle Status | Active (Recommended for new designs) |
| Manufacture's Sample Availability | No |
Packaging
| Pin | 16 |
| Package Type | RTE |
| Industry STD Term | WQFN |
| JEDEC Code | S-PQFP-N |
| Package QTY | 250 |
| Carrier | SMALL T&R |
| Device Marking | BSR |
| Width (mm) | 3 |
| Length (mm) | 3 |
| Thickness (mm) | .75 |
| Pitch (mm) | .5 |
| Max Height (mm) | .8 |
| Mechanical Data | Download |
Parametrics
| Number of Channels | 7 |
| Duty Cycle(Max) | 0.23 % |
| LED | 4+2+1 |
| LED Current Per Channel | 25 mA |
| Operating Temperature Range | -40 to 85 C |
| Package Group | WQFN |
| Package Size: mm2:W x L | 16WQFN: 9 mm2: 3 x 3(WQFN) PKG |
| Peak Efficiency | 93 % |
| Rating | Catalog |
| Shutdown Current(Typ) | 0.1 uA |
| Special Features | Analog Dimming,Enable/Shutdown,I2C Control,Integrated Switch,Load Disconnect During Shutdown,OVP,Soft Start,Synchronous Rectification |
| Switching Frequency(Max) | 875 kHz |
| Topology | Boost |
| Type | Capacitive |
| Vin(Max) | 6 V |
| Vin(Min) | 3 V |
| Vout(Max) | 6.5 V |
| Vout(Min) | 2.7 V |
Eco Plan
| RoHS | Compliant |
Design Kits & Evaluation Modules
- Evaluation Modules & Boards: TPS60250EVM-185
TPS60250 Evaluation Module
Lifecycle Status: Active (Recommended for new designs)
Application Notes
- MSP430 Interface to TPS60250 via I2C Master SoftwarePDF, 499 Kb, File published: May 1, 2008
The TPS60250 is a high-efficiency, constant-frequency charge pump dc/dc converter that can drive up to five white LEDs for a main display and up to two white LEDs for a subdisplay with regulated constant current for uniform intensity.A microcontroller (MCU) can be used to control the currents for white LEDs via the TPS60250 charge pump through a standard I2C interface, with the MCU acting as t - Ballast Resistor Calculation – Current Matching in Parallel LEDsPDF, 351 Kb, File published: Apr 16, 2009
Engineers often need to connect LEDs in parallel. Ideally, the LEDs share current equally. In reality, even LEDs from the same production lot have poorly matched I-V characteristics. This mismatch causes the LEDs to not share the current equally. The engineer can add a ballast resistor in series with each LED to minimize current differences. This application report explains how to size the ball - Extending the Soft Start Time Without a Soft Start Pin (Rev. B)PDF, 387 Kb, Revision: B, File published: Jun 15, 2017
- Performing Accurate PFM Mode Efficiency Measurements (Rev. A)PDF, 418 Kb, Revision: A, File published: Dec 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.
Model Line
Series: TPS60250 (2)
- TPS60250RTER TPS60250RTET
Manufacturer's Classification
- Semiconductors > Power Management > LED Driver > Backlight LED Driver
