RadioLocman.com Electronics ru
Advanced Search +
  

Datasheet Analog Devices ADIS16375

ManufacturerAnalog Devices
SeriesADIS16375

Low Profile, Low Noise Six Degrees of Freedom Inertial Sensor

Datasheets

  • Download » Datasheet, PDF, 795 Kb, Revision: D
    ADIS16375: Low Profile, Low Noise Six Degrees of Freedom Inertial Sensor Data Sheet
    Docket ↓
    FEATURES FUNCTIONAL BLOCK DIAGRAM Triaxis digital gyroscope, ±300°/sec
    Tight orthogonal alignment: 0.05°
    Triaxis digital accelerometer: ±18 g
    Delta-angle/velocity calculations
    Wide sensor bandwidth: 330 Hz
    High sample rate: 2.460 kSPS
    Autonomous operation and data collection
    No external configuration commands required
    Startup time: 500 ms
    Factory calibrated sensitivity, bias, and axial alignment
    Calibration temperature range: -40°C to +85°C
    SPI-compatible serial interface
    Embedded temperature sensor
    Programmable operation and control
    Automatic and manual bias correction controls
    4 FIR filter banks, 120 configurable taps
    Digital I/O: data-ready, alarm indicator, external clock
    Alarms for condition monitoring
    Power-down/sleep mode for power management
    Enable external sample clock input: up to 2.25 kHz
    Single-command self test
    Single-supply operation: 3.3 V
    2000 g shock survivability ...
  • Download » Datasheet, PDF, 47 Kb
    ADIS16375: Anomaly Data Sheet
    Docket ↓
    Silicon Anomaly Low Profile, Low Noise Six Degrees of
    Freedom Inertial Sensor
    ADIS16375 This anomaly list describes the known bugs, anomalies, and workarounds for the ADIS16375.
    Analog Devices, Inc., is committed, through future silicon revisions, to continuously improve silicon functionality. Analog Devices tries
    to ensure that these future silicon revisions remain compatible with your present software/systems by implementing the recommended
    workarounds outlined here. PERFORMANCE ISSUES
    Table 1. PROD_ID Register Contains Incorrect Value [ER001]
    Background
    Issue
    Workaround
    Related Issues The ADIS16375 provides a register for product identification, PROD_ID. This register contains the binary equivalent of 16,375, or
    0x3FF7. Prior to calibration, the automatic test software loads 0x0177 into the PROD_ID register, and then loads the
    register with 0x3FF7 after completing the calibration process. This requires operator input to verify passing units.
    Due to operator error, units that have a date code of 1118 did not complete the last step of the test procedure correctly,
    leaving PROD_ID = 0x0177, instead of 0x3FF7. These units are fully functional, passed all electrical testing, and meet the
    performance expectations stated in the data sheet, with the exception of the PROD_ID register.
    For systems that use the PROD_ID as a switch variable in the system firmware, add 0x0177 as a value that denotes ADIS16375.
    This issue has no effect on normal operation of these devices.
    None. ANOMALY STATUS
    Reference Number
    er001 Description
    PROD_ID register contains incorrect value Status
    Fixed Date Code ...

Prices

Status

ADIS16375BMLZ
Lifecycle StatusProduction (Appropriate for new designs but newer alternatives may exist)

Packaging

ADIS16375BMLZ
PackageMSM LAMINATE
Pins24
Package CodeML-24-6

Parametrics

ADIS16375BMLZ
Accel. In-Run Bias Stability(typ), g100
Accel. Range18 g
Calibrated Temp Range-40 to 85C
Degrees of Freedom, °6
Gyro Angular Random Walk(typ), °/rthr1
Gyro Axis to Axis Alignment(typ), °0.05
Gyro Bias Repeatability(typ), °/s1
Gyro In-Run Bias Stability(typ), °/hr12
Gyro Input Range +/-(min), °/s300
Gyro Linear G(typ)(, °/s)/g0.013
Gyro Noise Density(typ)(, °/s)/rtHz0.2
Operating Temperature Range, °C-40 to 105
Output Sample Rate(max), SPS2.46k

Eco Plan

Moldel Line

Series: ADIS16375 (1)

Manufacturer's Classification

  • Sensors > Inertial Measurement Units (IMU)
  • MEMS > Inertial Measurement Units (IMU)

Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus