Datasheet MAX22513 (Maxim) - 7

ManufacturerMaxim
DescriptionSurge Protected Dual Driver IO-Link Device Transceiver with DC-DC
Pages / Page46 / 7 — DC Electrical Characteristics (continued). PARAMETER. SYMBOL. CONDITIONS. …
File Format / SizePDF / 1.3 Mb
Document LanguageEnglish

DC Electrical Characteristics (continued). PARAMETER. SYMBOL. CONDITIONS. MIN. TYP. MAX. UNITS

DC Electrical Characteristics (continued) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Model Line for this Datasheet

Text Version of Document

MAX22513 Surge Protected Dual Driver IO-Link Device Transceiver with DC-DC
DC Electrical Characteristics (continued)
(V24 = 8V to 36V, V5 = 4.5V to 5.5V, VL = 2.5V to 5.5V, VDGND = VSGND = VGND = 0V, All logic inputs at VL or GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at V24 = 24V, V5 = 5V, VL = 3.3V and TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC CHARACTERISTICS / AUXILIARY INPUTS (RESET, FREQ)
RESETInput Voltage Low VRSTIL 3.05 V RESETInput Voltage High VRSTIH 0.8 V FREQ Input Voltage Low VFREQIL 3.05 V FREQ Input Voltage High VFREQIH 0.8 V RESETOutput Voltage Low VPOKLOW ILOAD = 5mA 0.2 V
DC CHARACTERISTICS / LOGIC INPUTS (SPI/I2C, CS/A0, SCLK, SDI/A1, SDO/SDA, TX, TXEN, LO/LI)
Logic Input Voltage Low VIL 0.2 x VL V Logic Input Voltage High VIH 0.8 x VL V Logic Input Leakage Current ILEAK Logic input = GND or VL -1 +1 μA
DC CHARACTERISTICS / LOGIC OUTPUTS (WU, IRQ, SDO/SDA, RX, LO/LI, MCLK)
Logic Output Voltage Low V WU, SDO/SDA, RX, LO/LI, MCLK, OL 0.2 V ILOAD = -5mA Logic Output Voltage High V WU, SDO/SDA, RX, LO/LI, MCLK, OH V I L - 0.3V V LOAD = +5mA IRQOpen-Drain High I Impedance Leakage Current LK_OD IRQnot asserted -1 +1 μA SDO/SDA Leakage Current ILK_SDO SPI/I2C = low, CS/A0 = high -1 +1 μA RX, LO/LI Leakage Current ILK_RXLI RX = LO/LI = GND or VL,DO_EN = 1 -1 +1 μA
DC CHARACTERISTICS / THERMAL CHARACTERISTICS
C/Q or DO/DI Per-Driver Driver temperature rising, C/Q or DO/ Shutdown Temperature TSHUT_DRV DI driver fault bit is set and driver is +150 °C disabled C/Q or DO/DI Per-Driver Driver temperature falling, driver is Shutdown Hysteresis TSHUT_DHYS automatically reenabled 8 °C IC Thermal Warning Die temperature rising, THERMW and Threshold TWRN THERMWINT bits are set +147 °C IC Thermal Warning Die temperature falling, THERMW bit Threshold Hysteresis TWRN_HYS is cleared 9 °C IC Thermal Shutdown Threshold TSHUT_IC Die temperature rising +170 °C IC Thermal Shutdown Hysteresis TSHUT_ICHYS Die temperature 17 °C www.maximintegrated.com Maxim Integrated │ 7