Rohde&Schwarz RTO2014 Oscilloscope

Product Brochure | Version 13.01 Probes and accessories
for Rohde & Schwarz
oscilloscopes Probes_and_accessories_bro_en_3606-8866-12_v1301.indd 1 16.07.2018 16:25:43 Probes and
accessories for
Rohde & Schwarz
oscilloscopes
At a glance
Test applications for oscilloscopes range from
debugging complex electronic circuits to measuring
the signal integrity of high-speed bus signals and
characterizing power electronics with dangerous
voltage levels. Measurement accuracy and operator
safety depend on the probes and accessories that
are used. Rohde & Schwarz passive probes are the perfect accessory for general measurement applications involving lowfrequency signals. The very fine, spring-loaded tip allows
precise and reliable contacting of signal lines.
Active broadband probes are ideal for applications where
low loading on the DUT is crucial or when the measured signal contains high-frequency signal components.
Rohde & Schwarz broadband probes feature a very low
load and a wide dynamic range. The integrated, highprecision DC voltmeter permits fast and easy testing (both
differential and single-ended) of DC voltage levels on signal lines, irrespective of the oscilloscope settings. The configurable, integrated micro button makes it easy to operate
the oscilloscope when measuring with multiple probes.
An extensive range of probe accessories ensures optimal
contacting. …

Data Sheet | V19.00 R&S®RT-Zxx
High Voltage and Current Probes
Specifications RT-Zxx_High_voltage_dat-sw_en_5214-2362-22_v1900_Cover.indd 1 19.03.2018 14:17:36 Version 19.00, March 2018 CONTENTS
Definitions. 3
Probe/oscilloscope chart . 4
R&S®RT-ZH03 high voltage passive probe . 6
R&S®RT-ZH10/-ZH11 high voltage passive probes . 9
R&S®RT-ZI10(C)/-ZI11 isolated probes . 12
R&S®RT-ZD002/-ZD003 high voltage differential probes . 16
R&S®RT-ZD01 high voltage differential probe. 19
R&S®RT-ZD02/-ZD08 high voltage differential probes . 22
R&S®RT-ZHD07 high voltage differential probe . 24
R&S®RT-ZHD15/-ZHD16 high voltage differential probe . 29
R&S®RT-ZHD60 high voltage differential probe . 33
R&S®RT-ZC02/-ZC03 current probes . 36
R&S®RT-ZC05B/-ZC10(B)/-ZC15B/-ZC20(B)/-ZC30 current probes . 40
R&S®RT-ZA13 probe power supply . 45
Ordering information . 46 2 Rohde & Schwarz R&S®RT-Zxx High Voltage and Current Probes Version 19.00, March 2018 Definitions
General
Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation
Specified environmental conditions met
Recommended calibration interval adhered to Specifications with limits
Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked …

Data Sheet | V18.00 R&S®RT-Zxx
Standard Probes
Specifications RT-Zxx_Standard_dat-sw_en_3607-3851-22_v1800_Cover.indd 1 18.12.2017 16:10:53 Version 18.00, December 2017 CONTENTS
Definitions. 3
Probe/oscilloscope chart . 4
R&S®RT-ZP03 passive probe . 5
R&S®RT-ZP05(S) passive probe . 8
R&S®RT-ZP10, R&S®RTM-ZP10 passive probes . 11
R&S®RT-ZP1X passive probe. 14
R&S®RT-ZL03/-ZL04 logic probes . 16
Ordering information . 18 2 Rohde & Schwarz R&S®RT-Zxx Standard Probes Version 18.00, December 2017 Definitions
General
Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation
Specified environmental conditions met
Recommended calibration interval adhered to Specifications with limits
Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked
with limiting symbols such as , ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is
derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if
applicable.
Specifications without limits
Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent
values with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance is ensured
by design. …

Data Sheet | V22.00 R&S®RT-Zxx
High Bandwidth Probes
Specifications RT-Zxx_High_bandwidth_dat-sw_en_3607-3868-22_v2200_Cover.indd 1 09.01.2018 13:24:07 Version 22.00, January 2018 CONTENTS
Definitions. 3
Probe/oscilloscope chart . 4
R&S®RT-ZZ80 transmission line probe . 6
R&S®RT-ZS10L active probe . 8
R&S®RT-ZS10/-ZS10E/-ZS20/-ZS30 active probes . 11
R&S®RT-ZS60 active probe . 16
R&S®RT-ZD10/-ZD20/-ZD30 differential probes . 19
R&S®RT-ZD40 differential probe. 24
R&S®RT-ZM15/30/60/90 modular probes . 27
R&S®RT-ZPR20/-ZPR40 power rail probes . 33
R&S®RT-ZA9 probe box to N/USB adapter . 36
Ordering information . 37 2 Rohde & Schwarz R&S®RT-Zxx High Bandwidth Probes Version 22.00, January 2018 Definitions
General
Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation
Specified environmental conditions met
Recommended calibration interval adhered to Specifications with limits
Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked
with limiting symbols such as , ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is
derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if
applicable. …

R&S®RTO2000
Digital Oscilloscope
Turn your signals
into success Multi
Domain Product Brochure | Version 09.01 year RTO2000_bro_en_3607-2684-12_v0901.indd 1 23.11.2017 14:54:08 R&S®RTO
Digital Oscilloscope
At a glance
R&S®RTO oscilloscopes combine excellent signal
fidelity, up to 16-bit vertical resolution and high
acquisition rate in a compact device format in the
600 MHz to 6 GHz class. They offer a fully integrated
multi-domain test solution with frequency, proto­
col and logic analysis functions. The brilliant
touchscreen makes the oscilloscopes very
comfortable to use. R&S®RTO oscilloscopes are optimized to perform precise
measurements at a high input sensitivity and very low inherent noise. The unique high definition mode enables up
to 16-bit resolution. With an acquisition rate of up to one
million waveforms per second, the R&S®RTO oscilloscopes
detect sporadic signal faults lightning fast.
R&S®RTO oscilloscopes are engineered for multi-domain
challenges and facilitate debugging of systems with different signal types. The oscilloscopes enable simultaneous
time, frequency, logic and protocol analysis and display
the results referenced over time. For the first time, a special tool is available for these applications: a zone trigger …

R&S®RTO
Digital Oscilloscope
Specifications Data Sheet | Version 16.01 year RTO2000_dat-sw_en_3607-2684-22_v1601_Cover.indd 1 07.11.2017 14:21:30 Version 16.01, November 2017 CONTENTS
Definitions . 4
Base unit . 5
Vertical system . 5
Horizontal system . 7
Acquisition system . 8
Trigger system . 9
RF characteristics . 11
Waveform measurements . 12
Mask testing . 13
Waveform math . 14
Search and mark function . 15
Display characteristics . 15
Input and output. 15 General data . 16
Options . 18
R&S®RTO-B1 . 18
Vertical system. 18
Horizontal system. 18
Acquisition system . 18
Trigger system . 18
Waveform measurements . 19 …

EUTRA/LTE NB-IoT
Measurement Application
Specifications Data Sheet | Version 03.01 R&S®FSW-K106
R&S®FSV-K106
R&S®FPS-K106
R&S®VSE-K106 VSE-K106_dat-sw_en_5214-7893-22_v0301_cover.indd 1 12.10.2017 18:21:52 Version 03.01, October 2017 CONTENTS
Definitions . 3
Specifications . 4
General remarks . 4
Overview . 4
Assignment of option numbers to link modes and access modes . 4
Running on a PC (R&S®VSE-K106) . 4
Running on a an instrument . 4
EUTRA/LTE analysis . 4
Signal acquisition . 4
Measurement parameters downlink . 5
Measurement parameters uplink . 5
Result displays downlink . 5
Result displays uplink . 6
Measurement uncertainty (nominal) . 6
Base station and UE output power . 6
Transmitted signal quality base station . 6
Transmitted signal quality UE . 7 Ordering information . 7 2 Rohde & Schwarz R&S®VSE-K106, R&S®FSx-K106, R&S®FPS EUTRA/LTE NB-IoT Measurement Application Version 03.01, October 2017 Definitions …

Data Sheet | Version 01.00 R&S®VSE-K96
OFDM Vector Signal
Analysis Application
Specifications VSE-K96_dat-sw_en_5215-3991-22_v0100_cover.indd 1 23.08.2017 16:52:35 Version 01.00, August 2017 CONTENTS
Definitions . 3
Specifications . 4
Minimum system requirements for the R&S®VSE-K96 . 4
OFDM vector signal analysis application . 4
Frequency . 4
Level . 4
Signal acquisition . 4
OFDM system configuration . 4
Measurement parameters . 5
Result displays . 5
Measurement uncertainty (nominal) . 5
Supported instruments. 6 Ordering information . 7 2 Rohde & Schwarz R&S®VSE OFDM Vector Signal Analysis Application Version 01.00, August 2017 Definitions
General
Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation
Specified environmental conditions met
Recommended calibration interval adhered to
All internal automatic adjustments performed, if applicable Specifications with limits
Represent warranted product performance by means of a range of values for the specified parameter. These specifications are
marked with limiting symbols such as , ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by …

R&S®RT-ZFxx
Oscilloscope Test
Fixtures
Specifications
R&S®RT-ZF1 USB 2.0 compliance test fixture set
The USB 2.0 compliance test fixture set contains a signal quality board and a load board for testing USB 2.0 (high speed),
USB 1.1 (full speed) and USB 1.0 (low speed). It is used in combination with the R&S®RTO digital oscilloscope, the R&S®RTO-K21
option and the R&S®ScopeSuite software.
General data
Temperature loading operating temperature range
storage temperature range Power supply 0 °C to +45 °C
-40 °C to +70 °C
5.0 V DC ± 0.25 V via USB R&S®RT-ZF2 Ethernet compliance test fixture set
The Ethernet compliance test fixture set contains the test fixture board and a network analyzer calibration board for testing the
physical layer of the Ethernet standards 10BASE-T, 100BASE-TX, 1000BASE-T and 10GBASE-T. It is used in combination with the
R&S®RTO digital oscilloscope, the R&S®RTO-K22 option and the R&S®ScopeSuite software.
General data
Temperature loading
Dimensions (W × H × L) operating temperature range
storage temperature range
test fixture board
calibration board 0 °C to +45 °C
-40 °C to +70 °C …

RTO-K21_bro_en_3606-9285-12.indd 1 Product Brochure | 02.01 Test & Measurement R&S®RTO-K21
USB2.0 Compliance Test
for R&S®RTO
digital oscilloscopes 18.03.2014 19:02:32 R&S®RTO-K21
USB2.0 Compliance
Test
At a glance The R&S®RTO-K21 USB2.0 compliance test software provides an automated solution for performing physical layer
tests on USB2.0/1.1/1.0 interfaces. It covers devices, hubs
and hosts. Integrated into the R&S®ScopeSuite software,
the solution allows experts and novices alike to complete
their tests quickly. Rohde & Schwarz offers the ­R&S®RT-ZF1
USB2.0 test fixture set for optimum contacting of the DUT.
When a Tabor WX2182B arbitrary waveform generator
is used, sensitivity tests for USB receivers are also fully
automated. The R&S®RTO-K21 software application checks the
signal conformity of USB devices in line with the
USB-IF compliance test procedures and ensures
the interoperability of products that have USB
interfaces. ❙❙ Test solution for USB2.0 devices, hosts and hubs in line
with USB2.0 compliance test procedures
❙❙ Support for all data rates: high speed (480 Mbit/s),
full speed (12 Mbit/s) and low speed (1.5 Mbit/s)
❙❙ Predefined, automated test steps …

R&S®RTO
Digital Oscilloscope
User Manual (=PïI2)
User Manual 1332.9725.02 ─ 11 This manual describes the following R&S®RTO models with firmware version 3.70:
● R&S®RTO2002 (1329.7002K02)
● R&S®RTO2004 (1329.7002K04) ● R&S®RTO2012 (1329.7002K12) ● R&S®RTO2014 (1329.7002K14) ● R&S®RTO2022 (1329.7002K22) ● R&S®RTO2024 (1329.7002K24) ● R&S®RTO2032 (1329.7002K32) ● R&S®RTO2034 (1329.7002K34) ● R&S®RTO2044 (1329.7002K44) ● R&S®RTO2064 (1329.7002K64) ● R&S®RTO1002 (1316.1000K02) ● R&S®RTO1004 (1316.1000K04) ● R&S®RTO1012 (1316.1000K12) ● R&S®RTO1014 (1316.1000K14) ● R&S®RTO1022 (1316.1000K22) ● R&S®RTO1024 (1316.1000K24) ● R&S®RTO1044 (1316.1000K44) © 2017 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: +49 89 41 29 -0
Fax: +49 89 41 29 12 164
Email: info@rohde-schwarz.com
Internet: www.rohde-schwarz.com
Subject to change - Data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of their owners.
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g. R&S®RTO is indicated as
R&S RTO. Basic Safety Instructions
Always read through and comply with the following safety instructions!
All plants and locations of the Rohde & Schwarz group of companies make every effort to keep the safety
standards of our products up to date and to offer our customers the highest possible degree of safety. Our
products and the auxiliary equipment they require are designed, built and tested in accordance with the
safety standards that apply in each case. Compliance with these standards is continuously monitored by
our quality assurance system. The product described here has been designed, built and tested in
accordance with the EC Certificate of Conformity and has left the manufacturer's plant in a condition fully …

®
R&S RT-ZF1 USB 2.0 Compliance
Test Fixture Set
Manual (=A[J2)
Manual Test & Measurement 1317.4326.02 ─ 06 This manual describes the R&S RT-ZF1 USB 2.0 Compliance Test Fixture Set
(1317.3420.02). © 2016 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: +49 89 41 29 -0
Fax: +49 89 41 29 12 164
Email: info@rohde-schwarz.com
Internet: www.rohde-schwarz.com
Subject to change - Data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
The following abbreviations are used throughout this manual: R&S®RTO is abbreviated as R&S RTO, and
R&S®ScopeSuite is abbreviated as R&S ScopeSuite. R&S®RT-ZF1 Contents Contents
1 Usage Information. 5
2 Product Description. 6
2.1 Deliveries. 6
2.1.1 Boards.6
2.1.2 Accessories.7
2.2 Test Equipment. 7
2.3 Specifications.8 3 Connections and Switches. 9 …

Probes_accessories_bro_ru_3606-8866-18_v1200.indd 1 Описание изделия | Версия 12.00  Пробники и
принадлежности для
осциллографов компании
Rohde & Schwarz 12.04.2018 08:16:58 Пробники и
принадлежности
для осциллографов
компании
Rohde & Schwarz
Краткое описание
Диапазон применения цифровых осциллографов
весьма широк — от наладки сложных электронных
цепей до анализа целостности сигналов
высокоскоростных шин и определения параметров
силовой электроники с высокими уровнями
напряжений. Точность измерения и безопасность
пользователя зависят от используемых пробников
и принадлежностей. Пассивные пробники компании Rohde & Schwarz оптимально подходят
для проведения общих измерений параметров низкочастотных сигналов. Высококачественные пружинные наконечники обеспечивают
высокие уровни точности и надежности подключения к сигнальным
линиям.
Активные широкополосные пробники идеально подходят для приложений, в которых низкий уровень нагрузки на испытуемое устройство
(ИУ) является ключевым фактором или в которых измеренный сигнал
содержит высокочастотные составляющие. Широкополосные пробники компании Rohde & Schwarz оказывают минимальную нагрузку на …

Цифровые
осциллографы
R&S®RTO2000
Turn your signals into
success Multi
Domain Описание изделия | Версия 07.00 year RTO2000_bro_ru_3607-2684-18_v0700.indd 1 11.04.2017 10:13:07 Цифровые
осциллографы
R&S®RTO2000
Краткий обзор
Осциллографы R&S®RTO сочетают превосходную
точность воспроизведения сигналов, 16-битное
разрешение по вертикали и высокую скорость
сбора данных в компактном устройстве с полосой
пропускания до 6 ГГц. Они представляют собой
полностью интегрированное решение для
проведения испытаний в нескольких областях с
использованием функций частотного, протоколь­
ного и логического анализа. Великолепный
сенсорный экран обеспечивает исключительное
удобство эксплуатации осциллографов. Осциллографы R&S®RTO оптимизированы для выполнения высокоточных измерений с высокой входной чувствительностью и очень
низким уровнем собственных шумов. Уникальный режим высокой четкости обеспечивает 16-битное разрешение по вертикали. Благодаря
скорости сбора данных до одного миллиона осциллограмм в секунду
осциллографы R&S®RTO позволяют мгновенно обнаруживать спорадические ошибки сигналов. …