Circuits & Schematics: 1 -Wire Barometer - 5/10 Volt Design vrs 2 - 2
Search for: "1 -Wire Barometer - 5/10 Volt Design vrs 2"
Search results: 1,580 Output: 11-20 Including: 10 (1091); Design (945); Wire (261); Volt (97); Barometer (3); vrs (0).
- .. state is zero. Below are the timing equations for the test circuit in Figure 5 built with IC1 = TLC393 , R4 = R6 = 10 kΩ, R5 = R7 = 22 kΩ, and +V S = 15 V. Note that V CS falls out of the equations, so the ’on’ time is ...05-04-2024
- .. back I published a simple design idea for a thermal airspeed sensor based on a self-heated Darlington transistor pair (Ref, 1). The resulting ...04-04-2024
- .. design for a photonic switch needs more than approximately 70 V at the cathode of a duo-lateral optical ...01-04-2024
- .. with R3. Some ’large’ (high current) MOSFETs have gate capacitances of tens of nanofarads, so with R1 = R3 = 10 kΩ it can take several milliseconds for the gate to discharge completely. Now, with C2 = 100 nF and R7 = 10 kΩ, Q3 ...
.. previous Design Idea [ 1 ] outlined a relatively simple circuit in which a momentary pushbutton could be made to function ...28-03-2024 - .. peak value to the signal end of R1, and adjust R8 for zero indication on the meter. Now apply the maximum level I chose +10 dBu and set R11 for full-scale deflection. R8 must be set first, then R11. Temperature stability is good. According ...
.. D3/R4 bootstrapping R3 to give a linear fall in voltage equivalent to 20 dB in 1.7 s, which, more by happy accident than by design, is exactly what we want. Now we pass the signal through D4, whose tempco of about 2 mV/ C compensates for ...21-03-2024 - .. a first-order temperature coefficient of 3.9 parts/1000/ C. As a result, the regulated current decreases about 4% for each 10 C increase in operating temperature. Materials on the topic Datasheet Maxim MAX1685 Datasheet Maxim MAX4162 Datasheet ...
.. source. For LEDs with currents greater than 0.35 A, an inductive switching regulator is usually the best choice. This Design Idea presents a series of circuits based on single-power-IC switching regulators, with efficiency and ...20-03-2024 - .. to the PCB including a jumper. Three wires are attached including the +5 V and ground from the USB cable. The other ground wire needs to be soldered to the BNC body. To do this, I had to break out the old Radio Shack 100 W soldering gun to ...
.. if the final design could attain a 500 ps rise time, this would be too large to ignore as it could give an error in the 10% range. But if we assumed a value for R P (or better yet pre-measured it) we could remove it after the fact. As ...18-03-2024 - .. improving efficiency-promoting synchronicity of charge transfer. Some performance spec’s (V+ = 5 V) are: Impedance of 10 V output: 8.5 Ω Maximum continuous load: 50 mA Efficiency at 50 mA load: 92% Efficiency at 25 mA load: 95% Unloaded ...
.. a design needs auxiliary voltage rails and the associated current loads are modest, capacitor pump voltage multipliers ...14-03-2024 - 12-03-2024
- .. and R14. The excitation employed comprises alternating-amplitude current-mode signals in the ratio of (almost exactly): 10:1 = (100 µA via R3 and R13):(10 µA via R2 and R14). With this specific 10:1 excitation, most every ...
.. heatsinks, thermoelectric coolers (TECs), and thermal control in electronic assemblies. Figure 1 illustrates an inexpensive design for a high-resolution differential thermometer utilizing the ∆V BE effect to make accurate measurements with ...06-03-2024
Sort by: relevance / date
Search "1 -Wire Barometer - 5/10 Volt Design vrs 2" on other search engines: Only-DataSheet.com Google
